LWN RF Flanges Common Dimensional and Installation Considerations

LWN RF Flanges: Common Dimensional and Installation Considerations

An LWN RF flange is a Long Weld Neck Raised Face flange, built with an extended tapered neck that welds to a pipe or vessel nozzle. The long neck merges the flange and the connecting pipe into a reinforced section, transferring pressure and mechanical loads over a wider length. Engineers specify this fitting in pressure vessel work and other demanding welded connections. Before finalizing a specification, it is critical to conduct research on the LNRF Flanges to ensure a comprehensive understanding of the dimensions, raised face, bore, bolting, and installation.

What Is an LWN RF Flange?

LWN stands for long weld neck; RF stands for raised face. A standard weld neck flange has a shorter tapered hub. A gasket seating surface is formed by the raised face of an LWN RF flange, which is defined by a longer, heavier barrel that extends the flange body further along the pipe run. In certain pressure vessel designs, this flange replaces a conventional weld neck flange paired with a separate pipe or nozzle section, combining two components into a single forged piece. Selection depends on the design conditions, the applicable code and the governing specification.

Common LWN RF Flange Dimensions

A defined set of dimensions must be confirmed before an LWN RF flange goes into a purchase order or fabrication drawing. These include nominal pipe size, outside diameter, flange thickness, overall or neck length, hub diameter and bore. Raised face diameter and height matter, along with the dimensions of bolt holes and the bolt circle diameter. Weld end dimensions close the list, since the flange must match the connecting pipe or nozzle at the joint. The bore should align with the connected pipe or nozzle’s wall thickness and inside diameter, while bolt hole dimensions must match the mating flange exactly, or the bolt will not seat. Reference sources point to ASME B16.5 for smaller nominal sizes and ASME B16.47 for larger sizes, but the applicable edition and project specification should be confirmed before any dimension is placed on a drawing.

Raised Face and Sealing Considerations

The raised face gives the gasket a defined, elevated contact surface separate from the bolt circle, concentrating compression where the seal needs it. That surface must match the mating component and the gasket selected for the joint. A mismatch between the raised face and gasket type undermines the seal regardless of bolt torque. Surface condition and alignment carry equal weight. Scoring, pitting or misalignment on the raised face compromises sealing even when every other dimension is correct. No single raised face height applies across the board; published dimensional tables show that raised face dimensions shift with flange class and nominal size, so the applicable standard governs.

LWN RF Flange Installation Considerations

Installation starts with verification. Confirm the flange size, pressure class, material grade and facing against the drawing before positioning it. Check that the bore and weld end dimensions match the connecting pipe or nozzle, then inspect the raised face for damage or contamination from storage or transport. Align the flange square to the mating component before tacking it in place. Complete the butt weld using the approved welding procedure for the material and thickness involved. Install the specified gasket and bolting, then tighten the bolts following the project’s sequence and torque or tension procedure, not an arbitrary pattern. Weld neck connections transfer stress into the pipe or nozzle through the neck itself, so alignment and weld quality require mechanical integrity. Required inspection and testing close out the installation before the joint enters service.

LWN RF Flange vs Standard Weld Neck Flange

Factor LWN RF Flange Standard Weld Neck Flange
Neck Longer, heavier barrel Tapered hub
Typical use Pressure vessel, nozzle and specialized connections  Process piping and equipment connections 
Connection Welded directly to pipe or nozzle Butt welded to pipe
Face Raised face in this configuration Can vary by specification
Design consideration Integral, self-reinforcing geometry Stress transition through tapered hub

Neither flange is universally stronger than the other. The design duty, the applicable code calculations and the specific pressure and temperature conditions determine which geometry fits a given connection.

How to Select the Right LWN RF Flange

Work through nominal size, pressure class and material grade first, then confirm the applicable dimensional standard for the project. Check the raised face requirements against the mating flange and gasket, and match the bore to the pipe or nozzle wall thickness. Verify the bolt hole pattern, gasket compatibility, and the operating temperature and pressure the joint will see in service. Confirm inspection and certification requirements before the flange ships, since these vary by project and by client specification. Tesco Steel & Engineering manufactures and supplies LWN RF flanges in stainless steel, duplex and super duplex steel, carbon steel, Inconel, Monel, Hastelloy, nickel alloy, copper nickel, titanium and other ferrous and non-ferrous materials. Contact Tesco Steel & Engineering to confirm dimensions and material certification for your specific project.